Hack wifi using Android
How to Hack WiFi Using Android?
Proceed only if your device falls under either of the below categories. Otherwise, it is waste of time and energy. For better results use Cyanogen ROM.
Android Device should be rooted.
Android Device should support bcmon App (i.e should have Broadcom bcm4329/4330 wifi chipset. [OR]
[Update] Now 'non bcmon supported devices' & 'devices which support external WiFi cards' can also be used to hack WiFi.
Tools Used:
bcmon app[apk] -This tool enables Monitor Mode on your rooted device with Broadcom chipset, which is essential for hacking WiFi using android. Download Link 1 or Download Link 2
Reaver for Android or RfA - A WiFi pentesting tool which can be used to attack WPS-enabled routers and after the WPS-Pin is cracked, it can retrieve the actual WPA-key. Download Link 1 or Download Link 2
Hacking WPA/WPA2 (WPS Enabled) WiFi using Android [bcmon supported devices]
Download and install the bcmon app.
Run bcmon. It may crash at first but keep trying. If it still crashes after 3-4 attempts the device may not be supported.
Install the firmware and tools, as prompted. Click on 'enable monitor mode'.
Download and install Reaver and run it.
Reaver will scan for the available access point. Remember it can hack only WPS enabled WiFi. Make sure Monitor Mode' is turned on. Make sure that the "Automatic advanced settings" box is checked.
Hacking WEP type WiFi Using Android Phone
WEP is an outdated, weak protocol used to secure WiFi and it is no more preferred because it can be hacked within seconds. However, due to lack of awareness, it is still used across the world. Below instructions explain how you can use your android device to hack a WEP protected WiFi network.
Procedure
bcmon app is used here also. So download and install it as told above
Tap "Run bcmon terminal". This will launch a terminal similar to most Linux terminals.
Type airodump-ng and tap the Enter button. In the newly opened window type airodump-ng wlan0 and tap the Enter button.
Open reaver and note down the WiFi (Access point) name, Mac Address and the broadcasting channel of the WiFi which you want to hack. Make sure it is WEP.
[7/16, 5:45 PM] Chahu Bhulana Tujhko....: Now we can start scanning the target WiFi and collect packets. Type the following
[7/16, 5:45 PM] Chahu Bhulana Tujhko....: airodump-ng -c channel# --bssid MAC address -w outputfile ath0
[7/16, 5:46 PM] Chahu Bhulana Tujhko....: Note: channel# = broadcasting channel, MAC address = Mac Address of the router which you already noted down. -w is for specifying the output file name. I have given the name as outputfile in the example. So the complete command looks similar to this.
[7/16, 5:46 PM] Chahu Bhulana Tujhko....: airodump-ng -c 9 --bssid 00:14:6C:7E:40:80 -w outputfile ath0
[7/16, 5:46 PM] Chahu Bhulana Tujhko....: Continue scanning untill it collects 20,000-30,000 packets.
[7/16, 5:46 PM] Chahu Bhulana Tujhko....: It might take hours to crack. Finally a message Key Found! will appear, followed by the key in a hexadecimal form. Key will work only if Probability" is 100%.
[7/16, 5:47 PM] Chahu Bhulana Tujhko....: Remove ":" from the key. i.e if it is 19:04:56:77:94, the key would be 1904567794
[7/16, 5:47 PM] Chahu Bhulana Tujhko....: There are many other methods to hack WiFi using Android. Stay tuned for more tricks
Bcmon download link 1 👉http://zipansion.com/2HZBA
Bcmon download link 2 👉
http://zipansion.com/2HZUg
Reaver download link 1 👉http://zipansion.com/2HZBA
Reaver download link 2👉
http://zipansion.com/2HZBA
Comments
Post a Comment